Hot stamping and printing machines for highest quality requirements

Hot stamping machines RF 82 and RF 90

The hot stamping machine in round-flat-technology for highest quality requirements

The hot stamping machine in round-flat-technology offers you clear benefits: It gives you more stamping quality and more efficiency by innovative foil feed, more performance and efficiency due to newly developed foil reel bins, more accuracy due to height-adjustable form bed and more productivity through non-tool quick changeover feature of mounting plate. Through the precise fitting of the mounting plate, re-adjusting of the stamping dies is redundant.

The hot stamping machine in round-flat-technik for highest quality requirements

More stamping quality and more operating efficiency due to new foil feed

More stamping quality and more operating efficiency due to new foil feed

The stamping foils are conveyed through spm steuer’s RF 82 and RF 90 with new methods: Directly after the nip, the foil is led off sharply upwards. This has two benefits:

Higher quality: Due to the fact that after the application, the foil webs are led off sharply upwards, they are not permanently exposed to the heat of the stamping dies. Therefore, they are less pre-activated. Consequently, when using specific foil qualities, an improvement of the stamping result and an increase in performance is achieved.

Easy handling: The foil feed provides optimum access to the stamping form, which makes it possible to re-adjust the stamping dies without any interference by the foil. For easy feed of a new foil web, the machine can be driven to a specific web feed position.

More performance and efficiency due to newly developed foil reel bins

More performance and efficiency due to newly developed foil reel bins

With their newly designed foil reel bins, the RF 82 and RF 90 provide various benefits. Two of them are:

Full speed through brake: Sounds paradox, but when taking a closer look, it makes sense. The newly developed foil brake allows adjustment of the foil web tension during machine operation. This makes machine stops for re-adjusting the tension of the foil webs mostly redundant.

Unrestricted utilization of foil reel bins: Foil rolls with a diameter of up to 125 mm with the RF 82 and 150 mm with the RF 90 can be used without restrictions at any position of the foil reel bin. The widths are 800 mm with the RF 82 and 880 mm with the RF 90. The individual rolls are separated from one another by separation discs of only 2 mm thickness.

Pressure adjustment virtually as quick as a wink through height-adjustable form bed

Pressure adjustment virtually as quick as a wink through height-adjustable form bed

With many other stamping machines using the cylinder principle, stamping is quite an affair. A miscalculation means reajusting, re-fitting and re-setting quite a few things. The RF 82 and RF 90 stick to the base, because they shift the adjustment of the nip to the form bed. The height-adjustable form bed means saving time and at the same time continuous quality:

Extreme reduction of setup time: A once fixed and set cylinder packing does not have to be change when requiring more of less pressure. The nip is adjusted to the pressure requirements through simple, fast and precise lifting or lowering of the form bed.

Cutting edge precision: Because the packing and thus the cylinder diameter remains unchanged when adjusting the pressure, there are no changes in print lengths and register. The 1/100 scale of the display allows optimum pressure adjustment.

Higher productivity due to non-tool quick changeover feature of mounting plate

Higher productivity due to non-tool quick changeover feature of mounting plate

The stamping dies of the RF 82 and RF 90 are mounted on a mounting plate, which is fixed precisely in the machine without using any tools. This also has two important benefits:

Less setup time: You can easily pull out the mounting plate. No tools are required to take out or switch the mounting plate. Fixing and unlocking the tool mounting plate is easily done via quick clamps.

Higher accuracy: Through the precise fitting of the mounting plate, possible registration inaccuracies are prevented. In most cases, re-adjusting of the stamping dies is redundant.

Here, you can find all technical data of the hot foil stamping machines RF 82 and RF 90:

Designation RF 82 RF 90
Output per hour up to 4.000 sheets up to 4.000 sheets
Sheet size, max. 570 x 820 mm 640 x 900 mm
Sheet size, min. 210 x 280 mm 290 x 450 mm
Sheet thickness, max. 0,75 mm 0,75 mm
Stamping format, max. 550 x 800 mm 620 x 880 mm
Gripper margin 8 – 10 mm 8 – 10 mm
Diameter of foil roll, max. 125 mm 150 mm
Distance of foil rolls,  min. 2 mm 2 mm
Foil pulls and programms 1 – 3 1 – 3
Cylinder diameter 540 mm 540 mm
Packing thickness, incl. printed sheet 1,5 mm 1,5 mm
Heating zones 3 3
Height-adjustable form bed, adjustment range –0,3 bis +0,3 mm –0,3 bis +0,3 mm
Stamping die height, standard 7 mm / 1/4" 7 mm / 1/4"
Pile height, feeder 350 mm 340 mm
Pile height, delivery 510 mm 540 mm
Nominal output, drive 8 kW 8 kW
Nominal output, heating and foil unit 18 kW 18 kW
Nominal frequency 50/60 Hz 50/60 Hz
Press length 4.000 mm 4.300 mm
Press width 2.600 mm 3.400 mm
Press height 1.750 mm 1.750 mm
Press weight (without pile) 5.500 kg 6.800 kg